- #Why is there no add outputs on compressor 4.4.1 how to
- #Why is there no add outputs on compressor 4.4.1 manual
There are two parts to the bullet-piercing device. Install a bullet-piercing device around the Freon line next to your compressor.
#Why is there no add outputs on compressor 4.4.1 manual
You can consult the manual of your fridge to identify which Freon line is connected to each pipe. The Freon line will connect directly to the tank and feed into your fridge. It cools and compresses hot air before putting it back in the fridge. The compressor tank is located behind the panel in the fridge’s bottom. Look for the compressor tank to locate the Freon pipe. You can store food in a cooler filled with ice if it is prone to melting or going bad quickly.Ģ. Slide the panel off, and then set it aside. Use a wrench or a screwdriver to loosen the bolts and screws. It is located at the bottom of the refrigerator. You will be able to access the back panel by turning it upside down. Take your refrigerator apart a bit, and then unplug it. Remove the screws from the back panel of your refrigerator.
#Why is there no add outputs on compressor 4.4.1 how to
This video will show you how to add Freon to your compressor.ġ. Plugin your refrigerator to check if it is working. The bullet-piercing valve is already in your Freon pipe, so it can’t be removed again.įinally, screw the back panel in place. Keep the cap on your adaptor, put it back, and save it for another day. Next, take the adaptor off the hose and disconnect it from the Freon line. Once Freon has been transferred to the Freon line connected to your compressor, turn clockwise to the valve on the tank replacement tank. Some tanks have gauges that show how much Freon you are releasing. Open the valve at the top of the replacement tank to add Freon. Make sure the hose fits on the adapter valve and the replacement tank. Next, connect the Freon pipe adaptor to the Freon hose. The tank should be connected to the hose. The tank will also come with a flexible hose. You should have ordered another tank that contains the same Freon as the one on your refrigerator label. You may wish to escalate the problem to the manufacturer or an expert in this situation. If your gauge reading falls within the Freon range indicated on the guide, it could be more serious than just adding freon. Freon specifications should not be used for another refrigerator. You can check the label on the refrigerator’s back or inside for this information. If it’s higher than 1psi, you can open the valve for 4-10 seconds to release some air. It should give a value between 0 to 1 psi. This means that your Freon line is not under pressure. The gauge should read 0 PSI if there is enough Freon in the refrigerator. Freon overdose can cause your refrigerator to stop working. It is crucial to get the right reading to determine if Freon should be added. This means that there is still Freon in your compressor. You will notice that Freon levels are on the blue side of the gauge. The Freon and pressure readings will be displayed. Next, wait about 10-15 seconds before attaching your air compressor gauge to an adaptor. Plug your fridge back into the socket to get Freon readings from your compressor This can be done with your hands.Īttach your conversion valve to where the cap was once you have removed it. You can remove the cap by turning it clockwise to access the pipe. There’s a cap on the side of your bullet-piercing device. Your bullet-piercing valve should be removed. You could endanger your health by letting it leak Freon or the air. Use your wrench to tighten it if it isn’t. Importantly, make sure the valve is tightly fitted around the Freon pipe. This valve will allow you to access the pipe without having to puncture it. Wrap the valve around the Freon line near the compressor. The bullet-piercing device has three nuts.
0 kommentar(er)
